Heating cables
The GuttaCABLE system is conceived to prevent frost formation or snow in gutters. GuttaCABLE avoids bursting of gutter’s descents, as well as possible seepage caused by cold. Its plug and integrated thermostat allows an easy installation and use, and in total safety.
Cables power of 30w/m guarantee you the necessary power to avoid snow or ice formation. When it’s cold, thermostat set in motion the cable. And when it’s warm, the thermostat avoid the cable to be set in motion uselessly and to waste energy.
Cable is made of Thermoplastic with a mechanic braid protection and of earth connexion, as well as a resistant protection overjacket UV (UV rays).
CE, IPx7
Reference | Length(m) | Power (Watt) |
GUTTACABLE-4 | 4 | 120 |
GUTTACABLE-5 | 5 | 151 |
GUTTACABLE-6 | 6 | 196 |
GUTTACABLE-10 | 10 | 293 |
GUTTACABLE-12 | 12 | 367 |
GUTTACABLE-14 | 14 | 419 |
GUTTACABLE-16 | 16 | 471 |
GUTTACABLE-20 | 20 | 627 |
GUTTACABLE-23 | 23 | 700 |
GUTTACABLE-30 | 30 | 919 |
GUTTACABLE-35 | 35 | 1103 |
GUTTACABLE-41 | 41 | 1265 |
GUTTACABLE-49 | 49 | 1440 |
GUTTACABLE-55 | 55 | 1719 |
GUTTACABLE-70 | 70 | 2062 |
Download Self Limiting ELP-AL High Temperature Heating Cable
Frost protection or temperature maintenance on pipe or tanks. Temperature maintenance in zone in chemical and petrochemical industry. Frost protection of condensation lines, steam pruge,. Temperature maintenance of rubber gas pipe analyser.
Storage in rolls, Finishing on site, Built-in cold terminations, High safety thanks to modular design.
Length adjustable on site, packed in rolls, the eltrace constant power parallel heating tape represents a saving in application and design time.
.
Reference | Module | Power | Voltage | Max Temp energized | Max. Length |
ELP-AL-BOT-30 | 1.00 m | 30 W/m | 230V | 170°C | 169m |
ELP-AL-BOT-30-3 |
1.75 m 1.75 m |
10 W/m 30 W/m |
230V 400V |
200°C 170°C |
190m 245m |
ELP-AL-BOT-45 | 0.81 m | 45 W/m | 230V | 165°C | 135m |
ELP-AL-BOT-60 | 0.70 m | 60 W/m | 230V | 150°C | 117m |
Aquacable Datasheet - Frost Protection Heating Cable
TThe AQUACABLE heating cable are designed to prevent any risk of bursting pipes due to freezing. Designed for protection against freeze your pipes.
Thanks to its electrical outlet and integrated thermostat, installation is simple, fast and safely. The power of 10 W/m cable prohibits overheating your pipes while ensuring optimum antifreeze protection. When it is cold, the thermostat switches the operation of the heating cable. And when it's hot, the thermostat prevents the passage of current for the purpose of saving energy.
The cable is made of Thermoplastic with mechanical protection braid and earthing and an outer sheath of protection. High Quality Product
Aquacable Datasheet - Frost Protection Heating Cable
Free download: TRACEBAC Datasheet
Electric heating cables type TRACE-BAC assure you the best electrical tracing. They are conceived to prevent the ice risk formation in condensat receptacle, retention receptacle...
With integrated thermostat, the heating cable for condensat receptacle allows an easy and safe use. Its thermostat allows the heating cable to be set in motion only when temperature in under 5°C.
The power of 30w/m and its incorporated thermostat forbid any overheating.
When it’s cold, the thermostat set in motion the cable heating. And when it’s war, thermostat avoid the cable to be set in motion in order to avoid any energy waste.
This cable is made of silicone with a waterproof thermostat.
References | Power | Length |
TRACEBAC-2 | 60W | 2m heating cable + 2m cold lead |
TRACEBAC-3 | 90W | 3m heating cable + 2m cold lead |
TRACEBAC-4 | 120W | 4m heating cable + 2m cold lead |
TRACEBAC-5 | 150W | 5m heating cable + 2m cold lead |
TRACEBAC-6 | 180W | 6m heating cable + 2m cold lead |
TRACEBAC-8 | 240W | 8m heating cable + 2m cold lead |
TRACEBAC-x | on demand | on demand |
CE, RoHS, IPx7
Free download: TRACEBAC Datasheet
Download ELP-S heating cable datasheet
Length adjustable on site, packed in rolls, the eltrace constant power parallel heating tape type ELP-S represents a saving in application and design time.
Protection from freezing or maintaining at low and medium temperatures of pipes or tanks. Maintaining of diesel oil lines at a given temperature, Maintained temperature of products in the agro-food Industry.
Advantages : Storage in rolls, Finishing on site, Built-in cold terminations, High safety thanks to modular design, Low cost price.
Download ELP-S heating cable datasheet
Read more: Constant Wattage Heating Cable - Silicone heat cable - ELP-S
Constant Power Heat Cable Datasheet
The main feature of parallel heating cables is to have a resistive wire wound spirally around an insulation. This makes it possible to obtain a constant power per linear meter whatever its length. The contact with the conductors is alternately depending on the length of the heating module (usually every meter, but this may vary depending on the needs).
The cable then forms a system of resistors in parallel powered by two conductors. When a voltage is applied in the conductors, the resistive heating wire receives the same voltage between all the points of contact, the power per linear meter of cable is then independent of its length.
The main applications of these constant power parallel heating cables are defrosting in cold rooms, joints, doors, trays, drain pipes, etc.
They are also widely used to prevent the formation of condensation water in control cabinets. They can also be used for frost protection of pipes, temperature maintenance of tanks, hoppers, elevators and other applications such as compressors, boilers, tanks, etc.
Constant Power Heat Cable Datasheet
1. fil résistant, cf. Table de résistance
2. Isolation primaire: PFA épaisseur: 0.80 mm (-0/+0.05 mm) / (6) 0.90 mm / (1) 1.0 mm
3. Tresse de protection métallique
Cu: 16 x 5 x 0.15 mm / (2) 16 x 5 x 0.20 mm / (3) 16 x 6 x 0.20 mm
4. Surgaine PFA épaisseur: 0.4 mm (-0/+0.05 mm) / (4) 0.7 mm / (5) 0.8 mm / (6) 0.6 mm
Résistance à +20°C (cf. Table)
Plage de Température: -60°C à +260°C
Test voltage (Ueff): 2.50 kV (conducteur/tresse)
Tension nominale (UO/U): 450/750V
Rayon de courbure:
1.08 – 1.71 Ohm/km: 25 mm
2.90 – 8000 Ohm/km: 15 mm
Température mini d’installation: -60°C
Résistance mécanique: 4 Joules
* Selon résistance et classe de température
La gamme ELK-SOL est principalement utilisée pour le chauffage par le sol de locaux d'habitation ou autres (bureaux, hôtels, établissements scolaires,…), pour la mise hors gel de sol de chambres froides et pour la mise hors neige de rampe de parking, trottoirs, allée de circulation, stade, terrain de sport.
CE, NF C-15 100, IEC 60-800 rev3
Classe M2 (1500N)
Test impact 5 x 9 joules
Résistance sur demande
Les câbles chauffants Eltrace type ELK-MI sont des éléments à isolant minéral permettant de résoudre la majeure partie des problèmes de chauffage haute température jusqu'à plus de 600°C et pour des tensions jusqu'à 500V.
Leur conception particulièrement robuste, permet des applications dans des conditions de fonctionnement extrêmes de température, de pression, de densité de puissance au mètre linéaire et de contraintes mécaniques.
Ces éléments sont finis en atelier.
Références | ELK-MI-CN | ELK-MI-SS | ELK-MI-INC |
Type de câble chauffant | Unifilaire | Unifilaire | Unifilaire |
Nature de la gaine extérieure | Cupro-nickel | Inox AISI 304 L | Inconel 600 |
Nature de l’isolant diélectrique | Magnésie (Mgo) | Magnésie (Mgo) | Magnésie (Mgo) |
Applications: | Hors chimie | Toute installation | Toute installation |
Température maximale Exposition | 350°C | <800°C | <800°C |
Température maximale d’utilisation: | 250°C | <600°C | >600°C |
Puissance maximale en Watts par ml: | < 60W/ml | < 110W/ml | < 240W/ml |
Longueur maximale de circuit de : <1 ml à 280 ml selon nature d’âme chauffante
Nature de l’âme chauffante: Selon résistance linéique Cuivre/Constantan/Tophet/Nickel Chrome
Tension d’utilisation: Jusqu’ à 500 Vac
Tension maximale Diélectrique:
1.5 kilovolt /1 mn : D> 3 mm
1 kilovolt/ 1mn : D < 3 mm
Résistance d’isolement :
Avant pose : > 100 Mégohms
Après pose : >30 Mégohms sous 500Vcc
Courant de fuite : < 2.2 mA par 100 ml à température ambiante
Rayon de courbure minimum: 6 fois le diamètre extérieur du câble chauffant
Espacement entre câbles chauffants: Minimum 20 mm
Température minimale d’installation: Minimum: –60°C d’ambiance
Domaine d’application: Industrielle/ ATEX ZONE 1 &2 / Corrosive
Agréments: SIRA II 2GD Ex e II T6 à T1, selon étude, SIRA 08ATEX3236 X- (Systeme)
Accessoires de fixation : ELAA-50, ELAA-75, Colliers inox 6.5 mm HEL111-93148 Lg:362 mm et HEL111-93058 Lg: 110 mm
Instruction de Montage : Voir INS –MI /2010 Rev 0
Certifications ATEX, CE
Eltrace self-regulating heating cables are used for frost protection for pipe, tanks, containers, as well as for deicing eaves gutter and descents.
Avoid frost in negative cold rooms. To maintain the temperature of pipes, tanks, containers ... May be cut to any length and avoid overheating. Easy to use.
RESISTIVE HEATING CABLES: Heating polyethylene cable, silicone heating cables, Mineral insulated heating cables